What Is Mobile Section | Mobile Power Section In Hindi 2020
Hello Friends आज मैं आपको Mobile Section के बारे में बताने बाला हूँ जैसा कि आप जानते हैं कि पिछले कई दिनों से हम अपने Website पर Mobile के Basic Component के बारे में आप को बताते आ रहा हूँ और आज Mobile Basic Component के सभी Tutorials Complete हो गया हैं इसी बिच अब बारी आती है Mobile Section की आज के इस Post में हम आपको बताने बाले है । Mobile में कौन -कौन से Section होते है और ये कैसे काम करता है ये सभी Knowledge हम आज जानेंगे तो आप हमारे इस Article को Last तक जरूर पढ़े ।यह भी पढ़े :- What Is Mobile Capacitor And Working
![]() |
Power Section |
Type Of Mobile Section
- Power Section .
- Network Section .
- Audio Section .
- Controlling Section .
- Monitor Section .
1 . Power Section
- Primary Supply From Battery Connector Positive (+) Point
- Secondary Supply From UEM IC (Power IC)
L.V.R ⇾ Polarized Capacitor ⇾ 2 Pin Diode Near Battery Connector ⇾ Non Polarized Capacitor Near PFO (PA) ⇾ All Vbolt Supply Components ⇾ PFO (PA) Power Amplifier ⇾ Doted Coil ⇾ Light Components 2 Pin Diode 3 pin Transistor Near Boost Coil ⇾ Samsung And Android Phone Light + IC ⇾ Touch Light ⇾ Vibrator Motor ⇾ Charging IC ⇾ Bluetooth IC Radio IC ⇾ Ringer IC ⇾ UEM IC (Power IC )
यह भी पढे :- How To Check Mobile On/Off Switch,Shorting And Leakage With Multimeter
Secondary Supply UEM IC (Power IC ) से निकलती है और Volume Key तक पहुँचती हैं । For Example :-
CPU ⇨ Flash IC , Ram IC ⇨ Sim IC Jack ⇨ Display (L.E.D) ⇨ R.F IC (Network IC) ⇨ On/Off Switch ⇨ RTC (Real Time Clock Crystal IC) ⇨ 26Mhz Crystal ⇨ Vibrator Motor ⇨ BSI Track Components ⇨ Memory Card Jack ⇨ Hand Free Jack ⇨ Charging IC ⇨ Touch Light ⇨ Camera Connector ⇨ Touch Connector ⇨ All Secondary Supply Components ⇨ Charging Jack ⇨ Blutooth IC , Radio IC ⇨ Volume key.
यह भी पढ़े :- MOBILE PRACTICALS क्या हैं ?और कौन ⁃ कौन से है.
Charging Solution
- Remove Non Polarized Capacitor Charging Track.
- Remove 4 Ball Diode.
- Remove Charging Jack.
- Remove And Change UEM IC (Power IC).
Charging Show But Battery Not Store
- Check And Change Battery.
- Check And Change Charger.
- Clean And Resold Charging Jack.
- Remove And Change Charging Jack.
- Low Heat On Charging IC.
- Dance and Change Charging IC.
- Remove Charging IC Apply 2 pin Diode.
- Low Heat On UEM IC (Power IC).
Note :- आज हमने इस Article में केबल Power Section के बारे में ही बताया हैं अगले Post में हम Network Section की बात करेंगे । अगर आपने अभी तक हमारे इस Website को Subscribe नहीं किया है तो Plz Subscribe कर ले ताकि जब भी मै Articles Publish करू तो आपको Email के द्वारा पता चल सके ।
यह भी पढ़े :- Mobile Tecnology Advance Research Papper
Consultation
आशा करता हू कि आप को Mobile Power Section समझ आ गया होगा अगर अभी भी कोई Doubt है तो आप हमसे निचे Comment में पूछ सकते हो मै पुरी कोशिस करूँगा आपके Comment का जबाब देने की और अपने दोस्तों के साथ इसे Social Media Platform पर Share जरूर करें । आप हमारे Articles को पढ़े इसके लिए दिल से धन्यबाद ।
0 Comments